The MORryde Cushioned Equalizer kit part # MR87ZR is the correct kit for your 2017 Keystone Outback Ultra Lite 278URL based on your axle capacity and wheelbase. Then to compensate for it replacing your shorter width equalizer you'd want to go with the shorter shackle kit part # MR58ZR which has shackles that are 2-1/4 inches long. view full answer...
Are you sure about the 165/80-13 tire size? I don't show that as a currently available tire size, could you have meant a 185/80-13?
In any event, a 175/80-13 tire measures 24 inches tall x 6.9 inches wide which would be slightly shorter at about 3/4 of an inch and roughly 1/2 inch narrower than your existing tires, assuming that they're a 185/80-13.
So, the tires should work fine for you, once again assuming your current size is 185/80-13. I'd recommend going with a radial tire, as they... view full answer...
Most likely yes but I don't have a way to verify what steps would fit your 2019 Keystone Outback 260UML. The Lippert Steps part # LC432690 do fit most standard RV step areas. The mounting bracket is 27-1/2 inches wide so you would want to verify you have the correct width to fit these. view full answer...
The Advent Air Replacement RV Air Conditioner for Coleman Setup w/ Start Capacitor # ACCOL150B was designed to replace Coleman setups like you have now so it would plug right into the same connectors your RV has and use your current Coleman controls as well. Since this has the start capacitor that comes with it your 20 amp power source would work fine. view full answer...
While do we have an option for you, since your Carrier unit's control board is in the distribution box, what you will need is a new AC unit, because just replacing the top unit won't allow your AC to work. So what you will need instead is the following Advent AC, and you can choose from either White or Black:
- White: Advent Air RV Air Conditioner w/ Air Distribution Box and Wall Thermostat - 15,000 Btu # ADV64FR
- Black: Advent Air RV Air Conditioner w/ Air Distribution Box and Wall... view full answer...
Normally for an slide out that is 71 inches wide the slide topper you'd need is the part # LCV000165063 but if you don't have 7 inches of clearance on either side of the box you'd have to order the next size down with the # LCV000231482.
Now for the 155 inch wide slide out the normal size would be the # LCV000168109 but if there was a clearance issue you could go down to the next size with the # LCV000163299 which is white. We don't have this size in black. view full answer...
Your 2016 Keystone Outback 324 CG uses 12 inch brake assemblies like the part # AKEBRK-6 but we don't have a way to determine what replacement shoes you'd need as it would be based on the brand of brake assemblies you have and we don't have a way to determine that. view full answer...
The closest replacement with an HDMI port to your cutout size is the iRV RV Stereo - Double DIN - HDMI, AUX, Bluetooth, App Control - 50W - 3 Zone - 12V Item # IRV64FR. It is smaller than your current cutout so I recommend getting a dash plate and cutting the required size hole in it for the stereo and then mount it to the wall and then mount the stereo to the dash plate. You can find these at your local auto parts stores. view full answer...
Since we know your 2019 Keystone Outback 210 URS has 3,500 lb axles the correct Lippert Road Armor is the part # LC696740 which is rated for 3,500-8,000 lbs.
Then for an upgraded Lippert Tandem Axle shackle and bolt kit you could use the # LC64FR. view full answer...
Thank you for all of the info you listed. Since you have a Dexter 3,500 lb trailer axle the correct bearing kit you need is the part # BK2-100 that you referenced which comes with the correct bearings, races, and seals. For grease I would recommend the heavy duty and waterproof Lubrimatic LMX Red Grease part # L11390. view full answer...
For 4,400 AL KO trailer axles the correct replacement brake assemblies are part # K23-478-00 for the left hand side and part # K23-479-00 for the right hand side. It is much easier to just replace the assemblies instead of trying to individually replace all of the components. It often ends up costing about the same as well. view full answer...
It is certainly possible to upgrade or downgrade for that matter the spring bars on a weight distribution system. That said, this is not an option for all weight distribution systems with the main factor being age and parts available.I am not sure which exact model you have as Reese/Draw-Tite make several and the correct springs bars will be based on said model. I can say that most of the newer systems are branded as Reese so there is a good chance the spring bars for the older Draw-Tite... view full answer...
The Adjustable Width Trailer Hitch Receiver for RVs part # 13703 will work great on your Keystone Outback as it's designed for I-Beam frames. It will work great for a generator as it offers plenty of support and can be used with a lot of different accessories like the 16x21 TorkLift Lock and Load SideKick Cargo Tray for 2" Hitches part # TLA7901 or 24x27 TorkLift Lock and Load Maximum Security Cargo Tray for 2" Hitches 500 lbs part # TLA7752. view full answer...
The Adco AquaShed part # 290-52244 that you referenced is for RV lengths between 26'1" - 28-1/2' long so yes this is the same size. view full answer...
Are you sure that the bolt pattern you have? It's not a standard trailer bolt pattern but is pretty close to the very common 5 on 4-1/2 inch like the # AM32238B.
I attached a help article on determining bolt pattern that you might check out to verify what you have. view full answer...
I really like the Yakima OnRamp # Y36FR because it has an ample amount of space between the bikes and the mounting clamps are attached to the middle of the rack instead of on one side so it will be easier to configure them. This can handle up to 66 lb bikes which will be perfect for your application (although it is recommended to remove the batteries during transit), can accommodate up to a 50" wheelbase, and will work with 3.25" wide tires, but you can add the Fat Tire Straps # Y23FR which... view full answer...
To determine if we have leaf springs that will fit your Keystone I would need to know the length of your current springs. Common sizes are 26 inches like the part # e22YR.
Your U-bolts would work fine. view full answer...
We have a black version of the Solera awning you referenced with the part # LCV000168104 and this does come with all the mounting hardware you'll need including an awning rail. view full answer...
I recommend using the TireMinder i10 TPMS for RVs and Trailers w/ Signal Booster # TM56FR. This kit includes 10 wheel sensors for your multiple trailers. You can leave the sensors on each trailer and will not need to move them from trailer to trailer. The TireMinder can store information for 4 different vehicles and up to 40 sensors.
Additional Sensors # TM-2Brass are available if you will require more for your multiple trailers.
Both the monitor and signal booster can be easily moved... view full answer...